Hello,
Many
of us face a lot of problem when we have to reinstall windows on our
computer or laptop. First thing we have to decide from where to install
windows? The options available are DVD or USB Pendrive..
First
thing, you should check whether your BIOS supports booting from USB.
Most of the computer/laptops support. But if your BIOS doesn’t, then
sorry, you cannot boot from a USB Pen drive.
Second thing, you need another computer with Windows installed with a DVD drive, to copy its contents later.
So let us start with the procedure now:
1) Run command prompt (cmd). This can be done by clicking start and typing typing cmd in Windows 7. In Windows Xp, click on start and then click on run. Type cmd and run.
2) Then run diskpart utility from command prompt, by typing ‘diskpart’ on command prompt and pressing enter. This will run the diskpart utility in a separate windows,
3) Now put in your pendrive...
In a USB port. Your pen drive must be atleast 4 GB, 8 GB pendrive is best for this purpose. Now go back to the diskpart console and type ‘listdisk’ and press enter. This will list the various storage devices available. You can see the size column of the disk and here we can see that ‘disk 2′ is our pen drive. Warning: In your computer it may be some other number. In our case it is ‘disk 2′.
4)
Then you have to type ‘select disk 2′ and press enter. Note: in our
case it is disk 2, in your case it may be disk3, or disk 1 or any other
number. You can enter ‘detail disk’ to see the details of the disk after
selecting it toverify that you have selected the correct disk. You can
see these steps in the image below:
5) Then you have to run a series of commands. The commands to be run in the order are:- clean
- create partition primary
- select partition 1
- active
- format fs=fat32
These steps are shown in the image below:
First
thing, you should check whether your BIOS supports booting from USB.
Most of the computer/laptops support. But if your BIOS doesn’t, then
sorry, you cannot boot from a USB Pen drive.Second thing, you need another computer with Windows installed with a DVD drive, to copy its contents later.
So let us start with the procedure now:
1) Run command prompt (cmd). This can be done by clicking start and typing typing cmd in Windows 7. In Windows Xp, click on start and then click on run. Type cmd and run.
2) Then run diskpart utility from command prompt, by typing ‘diskpart’ on command prompt and pressing enter. This will run the diskpart utility in a separate windows,
3) Now put in your pendrive...
In a USB port. Your pen drive must be atleast 4 GB, 8 GB pendrive is best for this purpose. Now go back to the diskpart console and type ‘listdisk’ and press enter. This will list the various storage devices available. You can see the size column of the disk and here we can see that ‘disk 2′ is our pen drive. Warning: In your computer it may be some other number. In our case it is ‘disk 2′.
5) Then you have to run a series of commands. The commands to be run in the order are:- clean
- create partition primary
- select partition 1
- active
- format fs=fat32
These steps are shown in the image below:
- assign
- exit
- The image below shows all the steps taken from the first step:
7) After the format is complete, put in your original Windows 7 DVD in your DVD drive, or if you have an .iso image of the DVD, mount that image using any virtual drive software like Power ISO.
- Now go to My Computer, and open the contents of DVD Drive. Press ‘ctrl+a’ to select all contents and copy all the contents by pressing ‘ctrl+c’.
- Now go back to My Computer and open the USB Drive and press ‘ctrl+v’ to paste all the contents of DVD into the USB Disk.
When the copy finishes, you are done just remove the USB Drive safely and use it to install Windows 7 in your computer/laptop.
just enjoy and share with your friends
LIKE our Page for daily UPDATES
Mandasi Technologies
Mandasi Technologies
No comments:
Post a Comment